Factory and building automation devices cover thermostat / HVAC controls, Wi-Fi Linked Sensors, Lighting Control, Doorbells and Security Systems, equipment controllers, sensors and inventory control. These devices can be line powered or battery powered. Power management is needed for PoE applications, display backlights, RGB LED indicator lamps, power load switching and buck and boost converters.
LCD Backlight LED Drivers
Factory or building automation devices use LCD displays for operator feedback and control.
Backlight LED strings are configured in series or series/parallel configurations that often require the supply voltage to be boosted from the PoE source. Multiple current sink drivers connect to long serial strings of WLEDs and therefore require a compliance voltage significantly higher than the battery voltage.
Panel size and resolution determine the number of white LEDs (WLED) required to produce the necessary screen brightness
Dimming techniques to control the brightness can range from simple linear LED brightness control to sophisticated high efficiency PWM control to achieve contrast ratios of typically 20,000:1
High accuracy current sinks to provide uniform backlight across larger panel sizes
High efficiency boost power conversion required to minimize demands on battery power consumption and maximize the battery life between charge cycles
Multiple series/parallel strings of WLED drivers to match the display panel needs
Multiple programming options from simple PWM signal control to full-featured I2C interfaces.
Advanced design, low drop-out current sinks with tight linearity characteristics to maintain constant LED current accuracy over all battery voltage extremes
High efficiency boost converters with integrated protection against LED open and short-circuit conditions
High Efficiency, Wide Voltage Range 30-LED RGB Driver
Overvoltage and Surge Protection ICs
Products designed for factory or building automation controllers need voltage rail on/off control to reduce standby or shutdown state power consumption or to enable/disable specific function circuits while the device is operating.
Integrated load switches provide internal power switching and are controlled by simple GPIO logic.
Eliminate the need for bias and level shift circuits associated with discrete MOSFET switches
Provides slew-rate limited turn-on with reverse current blocking and output discharge mode to de-select functions when not required to extend battery life.
Factory automation controllers use multicolor RGB LEDs for function indicator lamps. Indicator lamps show power or system status on devices that have LCD displays. For devices without displays, indicator lamps are needed to show power and status for all functions.
RGB LED drivers allow simplified programmable control of LED color and brightness
3-channel RGB LED drivers permit custom color control
4-channel RGBW devices allow for driving a white LED in addition to the RGB LED
Multiple programming options include I2C or ExpressWire to ease integration with a wide variety of processors and operating systems
Wide range of ramp up/down timing for slow fade in/out effects and complex repeating patterns
3-Channel RGB LED Driver with I2C Control, AutoBlinQ™
Buck and Boost Converters
Factory and Building Automation products are powered by line driven supplies, PoE or battery supplies. Line driven AC/DC power supplies can be poorly regulated and do not always provide specific voltage rails needed by application circuits. PoE and battery powered products need voltage step down or step up regulation depending upon a specific application.
Point of load voltage regulators provide a local supply rail with high efficiency
Single output high efficiency DC/DC switching regulators can provide either a step-up or step-down voltage output.
Applications requiring PoE typically need high efficiency power conversion, small PCB area and reduced component count. Kinetic Technologies offers a broad portfolio of product solutions which integrate the PD physical interface and DC/DC controller functions into a single package. Supporting solutions from a few watts up to the maximum allowed, Kinetic Technologies provides high efficiency power solutions for nearly every PoE PD application.
The AS11xx family of parts provide solutions for PD controller and integrated primary DC/DC controller with single output isolated or non-isolated solutions for IEEE802.3af (Type 1) and IEEE802.3at (Type 1 and Type 2) PDs. Higher power levels may be achieved using custom programmed PSEs or by implementing the LLDP software interface to enable 4-pair power delivery on the Ethernet cable. These highly integrated solutions provide industry leading performance in a small footprint with integration of front end rectification (AS1113 and AS1114), surge protection, advanced PoE and power management, enabling a flexible design.
The AS1113 and AS1114 PoE + DC/DC controller products address Type 1 PD applications. They are highly integrated CMOS solutions for PoE applications that provide seamless integration of Front End Rectification, Advanced Power Management, EMI Control and High Voltage Protection in the Industry’s smallest footprint.
The AS1138 targets both Type 1 and Type 2 PDs. It is a highly integrated CMOS solution for PoE PDs requiring input power up to 30 watts. The AS1138 integrates input Surge Protection, a digital PD controller, and a low-emission DC/DC controller onto a single die. The AS1138 implements the physical layer PD functionality as required by IEEE? 802.3af and IEEE? 802.3at. This includes 2-event classification, a Type 2 PSE detection indicator (ATDET) in addition to PD detection, under-voltage lockout, and hot-swap FET integration
13W/30W 802.3af/at PoE PD and Integrated DC-DC Controller
Kinetic Technologies’ EMI/ESD Suppression technology is the industry’s first and is used to improve EMC performance in Ethernet applications. What used to present as a design challenge is solved by this unique solution that offers EMC compliance for Ethernet connected devices. The physical interface of the PD data path to the outside environment is through the PHY. The PHY is also subject to ESD and surge events when an Ethernet cable is inserted. CM emissions are typically filtered by large passive devices located between the PHY and the LAN isolation magnetics. Kinetic Technologies offers the world’s first active ESD and EMI suppressor IC, a 4-channel device in which each channel connects to one wire of the two twisted pair sets. ESD performance, EFT-B and surge immunity, and CM emissions equal or exceed passive techniques while occupying a much smaller footprint.
CISPR22 and FCC Part 15, Class B requirements?for Radiated and Conducted Emissions.
IEC 61000-4-3/6 requirements for Radiated and Conducted Immunity, Level 3 or higher.